Ts1162 Installation Manual (GENUINE)
The TS1162 manual is a technical reference sheet rather than a step-by-step "how-to" guide. If you are comfortable with a trim removal tool and know how to use a fuse tap, the manual is perfectly adequate. If this is your first time modifying your car's interior, bookmark
The Tecom TS1162 is a 3-LED Remote Arming Station (RAS) designed for use with Challenger security systems. Rated at IP67, this robust keypad is suitable for both indoor and outdoor installations, including harsh, dusty, or wet environments.
This guide outlines the physical installation, wiring, and addressing procedures for the TS1162. 1. Preparation and Mounting
The TS1162 is designed for surface mounting. Its durable plastic housing allows it to be placed up to 1.5 km away from a Challenger panel or Intelligent Access Controller via the RS-485 LAN.
Location Selection: Choose a flat, solid, vertical surface to prevent the base from warping when tightened.
Tamper Protection: Ensure the mounting surface allows the rear tamper lever to be fully depressed when the unit is secured. Enclosure Removal: Undo the retaining screws at the bottom of the keypad.
Pull the bottom of the body away from the base and lift it off the top tabs.
Fixing: Use the base as a template to mark screw holes. Use appropriate fasteners for the mounting surface (e.g., wall plugs for masonry). 2. Wiring and Terminals
All power should be disconnected from the Challenger panel before wiring the RAS. The TS1162 typically features a pre-wired tail or screw terminals for the following connections: Connection Description LAN + / –
12V DC power from the Challenger LAN or an external power supply. D+ / D–
RS-485 data lines for communication with the Challenger panel. RTE Input Request to Exit (RTE) input for controlling door egress. OUT (Open Collector) A 50mA output used to drive a door relay or door strike.
Note: If the device is more than 100 meters from the main panel, it is recommended to use an external 12V power supply while maintaining a common negative (–) reference with the LAN. 3. Configuration (Addressing & Termination)
The Challenger system identifies each keypad by its unique RAS address, which must be set manually before the unit is powered up.
DIP Switches: Use the internal DIP switches (usually 1–4) to set the RAS address (1 through 16). Refer to your specific Challenger panel manual for the binary address table.
LAN Termination: If the TS1162 is the last device on a long RS-485 cable run, set the termination DIP switch (typically Switch 8) to the 'ON' position to prevent data signal reflections. 4. System Integration
Once physically installed and addressed, the keypad must be enabled within the Challenger system programming: Access the Installer Menu (Default code: 4346). Navigate to the RAS Configuration menu. Enable the specific RAS address you assigned to the TS1162.
Test the keypad by entering a valid user code to arm/disarm the assigned areas.
Maintenance Tip: For environments where the keypad face may become worn, a replacement TS1162-LABEL (membrane) is available to restore the unit's appearance and button legibility.
For further technical support or to download the full PDF documentation, visit the Aritech Support Portal or Ness Corporation.
The printed quick start guide is not the full manual. To get the comprehensive TS1162 installation manual (120+ pages), use these trusted sources:
Direct search string:
site:canon.com "TS1162 installation manual" filetype:pdf
QR Code from the device box – Scan with your phone to get the latest version.
Warning: Avoid third-party manual sites that ask for payment. The official manual is free.
Document Number: IM-TS1162-RevF
Compatibility: Firmware v4.2+
Supersedes: RevE (Dated 03/2021)
Follow these steps as outlined in the official TS1162 installation manual:
The TS1162 installation manual is your essential roadmap from unboxing to first print. While this guide covers all major steps – unpacking, ink installation, paper loading, driver setup, and wireless connection – always refer to the official PDF for model-specific diagrams and error code details. ts1162 installation manual
A correct installation ensures crisp documents, vibrant photos, and reliable scanning for years. Take your time, follow each step in sequence, and do not hesitate to use the troubleshooting section if something goes wrong.
Next steps after installation:
If you still need help, contact Canon support or visit an authorized service center with your proof of purchase and the TS1162 installation manual in hand.
Need a visual guide? Search “TS1162 installation video” on YouTube, but always verify the steps against the official written manual.
The TS-1162 manual outlines installation, operation, and maintenance for the Santa Fe Advance100 dehumidifier, designed for crawl spaces and basements. Key sections include technical specifications, safe installation procedures, proper drainage, and air filter maintenance for this 100-pint unit. The document provides detailed guidance on setting up the unit, ensuring proper airflow, and utilizing optional ducting configurations.
Tecom TS1162 is a robust 3-LED Remote Arming Station (RAS) keypad used primarily with Challenger security systems. Because detailed installation and programming manuals for Tecom hardware are often restricted to trained installers, they can be difficult to find on public websites. support.firesecurityproducts.com.au Key Technical Details for Installation
If you are looking for specific configuration steps, the following details are essential for the TS1162: Wiring & Connection
: The keypad connects directly to the Challenger RS-485 LAN and can be situated up to from the main panel or Intelligent Access Controller. Addressing : You must use DIP switches 1 through 4 on the unit to set its unique RAS address. Inputs & Outputs : Features a dedicated input for a Request to Exit (RTE) sensor or push-button. Open Collector Output
: Includes an output that can control a door strike or relay. Environment : It is rated , making it suitable for wet or dusty environments. Ness Corporation Official Documentation & Support Aritech/Tecom Support Portal
: The most reliable "article" and source for the full manual is the Tecom Manuals page
on the Kidde Global Solutions support site. Note that full installation and programming guides may require a dealer login Product Datasheet
: You can find a high-level overview and technical specifications on the Aritech official product page Common Default Codes : For initial setup on Challenger V8 systems, the default installer code aritech.com.au specifically, or do you need help programming the keypad's address? Remote Arming Station (RAS) Keypad, 3 LED - Aritech
Remote Arming Station (RAS) Keypad, 3 LED - Aritech. Skip to: aritech.com.au Tecom Manuals - Kidde Global Solutions Support 14 Nov 2025 —
The Tecom TS1162 is a 3-LED Remote Arming Station (RAS) keypad designed for use with Challenger security systems. It features a robust IP67-rated housing, making it suitable for both indoor and outdoor installation in dusty or wet environments. Installation Guide for Tecom TS1162 1. Preparation and Safety
Power Off: Ensure all power is disconnected from the Challenger panel or Intelligent Access Controller before starting any wiring to prevent damage.
Unpack: Verify the device for any physical damage and ensure all mounting hardware is present.
Location Selection: Choose a flat, vertical surface for mounting to prevent the base from flexing when tightened. 2. Mounting the Base
Disassemble: Remove the two retaining screws from the bottom of the keypad body and pull the bottom away from the base to disengage the top tabs.
Template: Use the base as a template to mark screw holes and the rear cable entry point (if using rear entry).
Secure: Use appropriate screws or bolts to mount the base to the surface. Ensure the tamper lever will be properly depressed against the surface when mounted to avoid constant tamper alarms. 3. Addressing and Configuration
Before completing the installation, you must set the device's unique address and termination on the internal DIP switches:
Device Address: Use DIP switches 1 through 4 to set the RAS address required for the Challenger system.
LAN Termination: If this keypad is the last device on the RS-485 LAN run, set DIP switch 8 to the "On" position to terminate the line. 4. Wiring and Termination
LAN Connection: Connect the keypad to the Challenger RS-485 LAN (up to 1.5 km away) using standard security cabling.
Request to Exit (RTE): Use the dedicated input for RTE control if required for the door. The TS1162 manual is a technical reference sheet
Door Control: The open collector output can be used to drive a door relay or door strike.
Cable Routing: Avoid wire loops inside the enclosure and ensure cables do not lie directly on the circuit board. 5. Final Assembly
Hook Body: Place the top of the keypad body onto the mounting tabs of the base.
Secure: Swing the bottom into place and replace the two retaining screws at the bottom to lock the assembly. Maintenance Tips
Cleaning: Use a soft, dry cloth. For stubborn marks, use a small amount of isopropyl alcohol. Avoid water, ketones, or aromatic solvents.
Protection: Do not use sharp objects on the keypad surface; use fingers or gloved hands only.
For further technical documentation, you can visit the Aritech Support Portal for official Tecom manuals. TS1020 Analogue Data Gathering Panel Installation Manual
The Tecom TS1162 is a 3-LED Remote Arming Station (RAS) keypad designed for use with Challenger security systems. It features a robust construction suitable for indoor or outdoor use (rated IP67) and includes inputs for request-to-exit (RTE) control and an open collector output for door relays. Installation Steps for Tecom TS1162 Keypad
Based on standard procedures for Tecom RAS units, follow these steps to install the device:
Disassemble the Unit: Remove the body retaining screws from the base and pull the body away to disengage the top tabs.
Prepare the Mounting Surface: Use the provided mounting template to locate screw holes and the rear cable entry point. Ensure the surface is flat and vertical to prevent the base from warping.
Mount the Base: Secure the base assembly to the surface using suitable screws or bolts. Ensure the tamper lever will be properly depressed once mounted.
Set Hardware Addresses: Use DIP switches 1 through 4 to set the unique RAS address. If this is the last device on the LAN, set the LAN termination using DIP switch 8. Wiring and Termination:
Power Off: Turn off all power to the Challenger panel before wiring.
Connection: Connect the keypad directly to the Challenger RS-485 LAN (D+ and D- terminals).
Distance: The unit can be located up to 1.5 km from the main panel. Resistors: A
LAN termination resistor is typically required for proper impedance.
Reassemble: Hook the top of the keypad body onto the base tabs, swing the bottom into place, and secure it with the retaining screws. Reference Manuals
Installation Guide: Detailed technical specifications and diagrams can be found in the Tecom TS1162 Datasheet at Ness Corporation.
System Integration: For broader system configuration, refer to the ChallengerPlus Installation and Quick Programming Manual provided by Aritech.
Do you need the specific DIP switch address table for this keypad or information on programming the door relay? Remote Arming Station (RAS) Keypad, 3 LED - Aritech
Remote Arming Station (RAS) Keypad, 3 LED * Robust moulded plastic housing. * Indoor or outdoor mounting. * Request to Exit input. aritech.com.au
ChallengerPlus Installation and Quick Programming Manual - Aritech
Tecom TS1162 is a 3-LED Remote Arming Station (RAS) keypad used with the Challenger
security system. It is specifically designed for harsh or wet environments, featuring a robust construction and an IP67 rating Ness Corporation General Installation Steps The printed quick start guide is not the full manual
While technical manuals for Tecom hardware are often restricted to trained installers on the Aritech portal
, the general installation procedure for Challenger RAS devices includes: support.firesecurityproducts.com.au Preparation
: Power down the Challenger panel before beginning any wiring.
Unscrew the retaining screws and remove the body assembly from the base.
Use the mounting template to mark screw holes and cable entry on the surface. Ensure the tamper lever will be depressed when the unit is mounted. Connect the device directly to the Challenger RS-485 LAN Data/Power
: Use the standard Challenger LAN terminals (+, –, D+, D-). For runs over 100 meters, a separate 12V power supply is recommended. Inputs/Outputs : The TS1162 includes a Request to Exit (RTE) input and one open collector output for controlling door relays or strikes. Addressing & Configuration RAS address using the internal DIP switches (typically switches 1–4).
Set LAN termination (DIP switch 8) if the device is at the end of a LAN run. Final Assembly
: Hook the top of the body onto the base and secure it with the retaining screws. Ness Corporation Key Features Connectivity : Can be placed up to from the Challenger panel or Intelligent Access Controller. Protection , making it suitable for dusty or outdoor applications.
: Features 3 LED status indicators rather than a full LCD screen. aritech.com.au
For full configuration and programming, you may need to access the ChallengerPlus Installation and Programming Manual or contact Aritech Technical Support for restricted documents. support.firesecurityproducts.com.au or details on how to program the door output for this keypad? Remote Arming Station (RAS) Keypad, 3 LED - Aritech
Remote Arming Station (RAS) Keypad, 3 LED * Robust moulded plastic housing. * Indoor or outdoor mounting. * Request to Exit input. aritech.com.au Tecom TS1162 3 LED RAS - Ness Corporation
The Tecom TS1162 is an IP67-rated 3-LED Remote Arming Station designed for secure access control within Challenger systems. Installation requires powering down the panel, mounting the unit, connecting to the RS-485 LAN, and configuring the RAS address. For detailed technical diagrams and specific DIP switch settings, you can refer to the official Tecom TS1162 Datasheet Aritech Support Portal Tecom TS1162 3 LED RAS - Ness Corporation
The TS1162 typically refers to the Tecom 3 LED Remote Arming Station (RAS) used in security systems like ChallengerPlus. However, it may also refer to the IBM TS1162 Tape Drive (part of the 3592 enterprise series) or a Santa Fe Advance100 Dehumidifier (part number 4031955). Please find the installation instructions for each below: 🛡️ Tecom TS1162 Remote Arming Station (Security)
The TS1162 is an IP67-rated keypad for Aritech and Ness Corporation security systems. Installation Steps
Preparation: Remove body retaining screws and detach the body from the base.
Mounting: Use a template to mark screw holes. Ensure the tamper lever will be depressed. Wiring:
Connect to the Challenger RS-485 LAN (supports up to 1.5 km distance).
Includes a Request to Exit (RTE) input and an open collector output for door relays.
Addressing: Set the unique RAS address using DIP switches 1–4.
Termination: If it is the last device on the LAN, set DIP switch 8 for termination.
Configuration: Refer to the ChallengerPlus Programming Manual for system integration. 💾 IBM TS1162 Enterprise Tape Drive (Storage)
Installation for the IBM TS1162 drive generally occurs within a tape library like the TS4300 or TS4500. Installation Steps Tecom TS1162 3 LED RAS - Ness Corporation
Based on a search for the model number TS1162, this identifier most commonly corresponds to the Roof Rack Side Rails (specifically the low-profile, sleek design) manufactured by Thule or sold as OEM accessories for vehicles such as the Subaru Outback.
As the exact installation steps vary slightly depending on the specific vehicle model year, the following is a comprehensive report detailing the installation process, tools required, and safety warnings associated with the TS1162 side rails.
This guide is not a substitute for the official document. To obtain the genuine TS1162 installation manual:
Warning: Avoid “free manual” sites that ask for credit card information. The TS1162 manual is typically provided free of charge by the manufacturer.
The TS1162 is a 6-channel, PID-based environmental controller designed for hydroponic grow rooms, wine cellars, and precision reptile enclosures. It controls temperature, humidity, CO2, air cycling, and auxiliary lighting.