Lenel Lnl-3300-m5 Installation Manual Upd Here
The Lenel Lnl-3300-m5 Installation Manual UPD is not just a minor revision; it is a mandatory read for anyone integrating this controller into a modern IP access control system. The updates to PoE, OSDP wiring, and cybersecurity defaults reflect the industry's shift toward smarter, safer installations.
Always keep a copy of the latest manual in your service vehicle. A failed installation caused by referencing a Rev 4.0 manual when you have a Rev M5 board will cost you more in truck rolls than the price of the hardware.
Disclaimer: This article is for informational purposes and does not replace the official Lenel Installation Manual. Always follow local building codes and Lenel’s specific instructions for your hardware revision.
Lenel LNL-3300-M5 is an Intelligent System Controller designed specifically for migrating legacy CASI-RUSCO M5 and M3000 hardware to the
access control system. It serves as a plug-compatible CPU replacement that allows users to keep existing field wiring and enclosures while upgrading to modern security features. Amazon.com Key Features LENEL LNL-3300-M5 Intelligent System M Series Controller
The Lenel LNL-3300-M5 Intelligent System Controller allows for the rapid modernization of legacy CASI Micro/5 security systems by providing a drop-in, plug-and-play hardware replacement. This "plug-and-play" upgrade capability eliminates the need for extensive re-wiring, enabling a seamless transition to modern, networked security infrastructure within existing enclosures. For installation and update details, refer to the official documentation. Lenel Lnl-3300-m5 Installation Manual UPD
Lenel LNL-3300-M5 Installation & Migration Guide The Lenel LNL-3300-M5 Go to product viewer dialog for this item.
is an Intelligent System Controller (ISC) designed specifically for the OnGuard® system. It serves as a plug-compatible, Mercury-based hardware replacement for legacy CASI M5 and M3000 boards, facilitating a modern migration path for systems like Picture Perfect, FCWnx, and Secure Perfect. 1. Pre-Installation Preparation
Before beginning, ensure you have the following requirements and tools: Operating Voltage: 12 VDC ± 10% at approximately 300mA.
Backplane Compatibility: The board is designed to retrofit into legacy CASI M5/M3000 enclosures.
Connectivity Hardware: A standard Cat5/6 cable for Ethernet and shielded twisted pair (24 AWG) for RS-485 downstream communication. The Lenel Lnl-3300-m5 Installation Manual UPD is not
System Software: OnGuard software must be licensed and configured for the LNL-3300 series.
Important Note: Legacy CASI M Series boards cannot be mixed with Lenel M Series boards in the same controller; if you convert a controller, all boards within it must be upgraded to the Lenel M Series. 2. Physical Installation Steps To install or migrate to the LNL-3300-M5
Power Down: Completely power down the legacy controller and disconnect the backup battery.
Unplug Wiring: Label and unplug the field wiring and the power/comm board connectors from the legacy CPU.
Remove Old Board: Unscrew and remove the legacy M5/M3000 CPU (e.g., E, P, PX, PXN, or PXNplus) and the CASI Power/Comm Board (PN: 110064001). Insert LNL-3300-M5 Disclaimer: This article is for informational purposes and
: Mount the new board onto the existing standoffs in the enclosure.
Reconnect Wiring: Plug in the 12 VDC power input, cabinet tamper input, and AC power fail inputs. The LNL-3300-M5 is one-for-one plug compatible with these connections. 3. Initial Configuration & IP Setup LNL-3300-M5 - Stebilex Systems
If you are installing in a regulated facility (government, banking, healthcare), the UPD manual emphasizes:
For those looking for the PDF, you can grab the updated installation guide directly from the support portal or via the backup link below:
[LINK: Lenel LNL-3300-M5 Installation Guide (PDF)]
(Note: Make sure you have the "M5" specific revision. Earlier revisions for the standard 3300 don’t cover the updated dip switch configs for OSDP.)
