Download the driver from HP’s website (HP acquired the printer legacy from Samsung’s printer division, which had Olivetti compatibility). Alternatively, use the built-in “IBM Graphics 9-pin” driver.
Recommended: Use the Citizen or Epson FX-850 driver available in Windows 10’s driver list.
Report ID: ITD-2024-OLI-001
Date: October 26, 2024
Author: Technical Support Division
Objective: To provide a step-by-step procedure for installing and configuring the Olivetti PR2 Plus (often used for bank check printing, passbooks, or continuous forms) on a Windows 10 operating system.
While the Olivetti PR2 Plus is an older model, it is fully compatible with Windows 10 if you install it manually via "Have Disk" and ensure your port settings are correct. It remains one of the best printers for heavy-duty form printing!
Have you found a specific driver that works better? Let us know in the comments below!
Installing the Olivetti PR2 Plus passbook printer on Windows 10 can be tricky because it often requires manual configuration rather than a simple plug-and-play setup. While the hardware is robust, modern operating systems sometimes struggle to recognize its specialized interface. Step 1: Physical Connection and Preparation
Before starting the software setup, ensure the hardware is properly connected:
Power Down: Always turn off both the printer and computer before connecting cables.
Interface Choice: Connect via the USB port or Serial/Parallel port.
Power On: Turn on the printer's main switch (located on the left side) and then boot your PC. Step 2: Manual Driver Installation
If Windows does not automatically detect the printer, you must add it manually: Microsoft Support Fix printer connection and printing problems in Windows
Installing an Olivetti PR2 Plus passbook printer on Windows 10 can be tricky because the system often fails to recognize it automatically. This guide provides a step-by-step walkthrough to get your hardware communicating perfectly with your PC. Preparing for Installation
Before you begin, ensure you have the correct cables. Most PR2 Plus models use a standard USB Type-B to Type-A cable or a Serial (RS-232) connection. Turn off the printer.
Connect the printer to a USB port on your Windows 10 computer. Turn the printer back on.
Check if Windows detects a "New Hardware Found" notification. If it does not, you will need to proceed with a manual installation. Step 1: Download the Official Drivers
Windows 10 rarely includes the Olivetti PR2 Plus drivers in its pre-installed library. You must source them manually.
Visit the official Olivetti website or a trusted driver repository. how to install olivetti pr2 plus printer on windows 10
Search for the "Olivetti PR2 Plus Windows 10 Driver" or the "Universal Driver."
Download the ZIP file and extract it to a folder on your desktop. Step 2: Manual Installation via Control Panel
Since this printer is often used for specialized banking or administrative tasks, the "Add a printer" wizard is the most reliable method.
Open the Control Panel and navigate to Devices and Printers. Click Add a printer at the top of the window.
Click the link that says "The printer that I want isn't listed."
Choose the last option: "Add a local printer or network printer with manual settings" and click Next.
Select the port. If you are using a USB cable, select USB001 (Virtual printer port for USB). If using a serial cable, choose COM1. Click Next. Step 3: Assigning the Driver
Now you must tell Windows which driver to use for the hardware. Click the Have Disk... button.
Click Browse and navigate to the folder where you extracted the downloaded drivers.
Look for an .inf file (often named pr2plus.inf or similar). Select it and click Open, then OK.
Select Olivetti PR2 Plus from the list of models and click Next.
Follow the remaining prompts to name the printer and choose whether to share it on the network. Step 4: Configuring Emulation Settings
The Olivetti PR2 Plus is famous for its "Emulation" modes, which allow it to act like other printers (such as Epson or IBM models). If the printer prints garbled text or symbols, the emulation settings likely do not match your software.
Right-click your printer in Devices and Printers and select Printer Properties. Go to the Device Settings or Advanced tab.
Ensure the emulation matches what your specific application requires (usually Olivetti, IBM PP II, or Epson LQ).
If you need to change this on the physical printer, hold the Station 1 and Station 2 buttons while turning the printer on to enter the setup menu. Troubleshooting Common Issues Download the driver from HP’s website (HP acquired
Printer Status "Offline": Check the USB connection and ensure no other print jobs are stuck in the queue.
Prints on One Line: This is usually a driver conflict. Ensure you are using the "PR2 Plus" specific driver rather than a generic "Text Only" driver.
Driver Signature Error: Windows 10 may block the driver if it isn't digitally signed. You may need to restart Windows in "Disable Driver Signature Enforcement" mode to complete the installation. Final Verification
Once installed, go to Printer Properties and click Print Test Page. If the passbook printer feeds the paper and prints clearly, your installation is successful.
Installing the Olivetti PR2 Plus passbook printer on Windows 10 is straightforward but often requires manual driver selection and potentially enabling legacy system components. While official drivers support Windows 10 (32/64-bit), the printer might not always be detected automatically via USB. Step-by-Step Installation Guide
Title: Comprehensive Guide: Installing the Olivetti PR2 Plus Printer on Windows 10
Abstract The Olivetti PR2 Plus is a specialized dot matrix passbook printer widely used in the banking and financial sectors. Because this hardware was designed prior to the release of Windows 10, installing it on modern operating systems often presents compatibility challenges. This paper outlines the step-by-step methodology for successfully installing the Olivetti PR2 Plus on Windows 10, focusing on driver selection, port configuration, and emulation settings.
Before beginning the installation process, ensure the following requirements are met:
To install the Olivetti PR2 Plus passbook printer on Windows 10, you must manually point Windows to the correct driver, as it often fails to detect it automatically. Step 1: Download & Initial Setup Before starting, ensure the printer and computer are when connecting the cable. Olivetti SpA Download Drivers : Visit the Olivetti Techcenter
or a specialized repository to download the Windows 7/8 64-bit driver (often version ), which is compatible with Windows 10. Enable .NET Framework : Some users report needing enabled via the command prompt for full compatibility. Komdruck AG Step 2: Manual Installation If the printer is not automatically recognized: Settings > Devices > Printers & Scanners Add a printer or scanner , then select "The printer that I want isn't listed" Add a local printer or network printer with manual settings and click Next. Select Port : Choose the USB001 (Virtual printer port for USB)
or the appropriate COM/LPT port if using a serial/parallel adapter. Install Driver , browse to your extracted driver folder, and select the Olivetti PR2 Alternative
: If the specific Olivetti driver fails, some banking setups utilize the IBM Graphics 9pin driver as a compatible fallback. Step 3: Configuration & Testing Add or install a printer in Windows - Microsoft Support Select Start > Settings > Devices > Printers & scanners . Microsoft Support
How to Add a Printer in Windows 10 - University of Colorado Boulder
Windows 10 might not always automatically detect the PR2 Plus. It is essential to use a compatible driver.
Official Drivers: Visit the Olivetti Download Center to find the latest official software.
Alternative Versions: If the Windows 10 specific driver isn't listed, many users have successfully used the Windows 7 (32/64-bit) v09 driver in compatibility mode. The Olivetti PR2 Plus supports three main interfaces:
Third-Party Repositories: Sites like Komdruck AG or Driver Scape host archived versions of the PR2 driver if the official site is unavailable. 2. Physical Setup & Connection Before diving into software, ensure the hardware is ready.
Remove Shipping Locks: Open the printer cover and remove the red plastic clips holding the print head carriage in place.
Choose Your Interface: The PR2 Plus typically supports USB, Serial, and Parallel connections. For Windows 10, USB is the most common. Power On: Connect the power cable and turn the printer on. 3. Installation Steps
Once you have the driver file (usually a .zip or .exe), follow these steps:
Unzip the Driver: Extract the files to a folder on your desktop. Add Manual Printer: Go to Settings > Devices > Printers & Scanners.
Click Add a printer or scanner, then select The printer that I want isn't listed.
Choose Add a local printer or network printer with manual settings. Select the Port:
For USB connections, select an available USB Virtual Printer Port (e.g., USB001). Install Driver:
Click Have Disk and browse to the folder where you extracted the driver files.
Select the Olivetti PR2 model and follow the remaining prompts to name the printer and finish installation. 4. Configuration & Testing
To ensure the best print quality, you may need to tweak a few settings. Download drivers | Olivetti SPA
Assurance and support * Download Area. * Services center. * Warranty. Olivetti SpA
Important: Olivetti does not provide an official Windows 10 driver for the PR2 Plus. However, you can use a generic driver that fully supports IBM Proprinter emulation.
This is a critical step often overlooked during manual setups.
The Olivetti PR2 Plus supports three main interfaces:
Recommendation: Use USB if possible. It simplifies driver management.