| Problem | Solution |
|---------|----------|
| Drive not detected | Reinstall driver, use USB 2.0 port |
| Error "Load FW Fail" | Firmware missing – check folder for .bin files |
| Capacity shows 0 MB | Bad blocks – reduce capacity setting |
| Status "Failed" (red) | Retry with "Normal" format, disable bad block check |
| Windows doesn't recognize after | Reformat with Diskpart or Windows Disk Management |
Before formatting, you must load the correct parameters.
Unlike normal software, there is no setup.exe or installer. The “installation” is simply extracting a compressed folder.
Installation rating: 2/5 for user-friendliness, 5/5 for portability.
No bloatware, no registry changes, no background services. But the lack of a real installer confuses casual users.
Product Name: FirstChip MPtools v1052 – FC1178/FC1179 Edition
Type: Firmware flashing, low-level formatting, and USB mass-production tool
Supported Controllers: FirstChip FC1178, FC1179
Version: 1052 (fictional but following versioning logic similar to existing MPtools like v1.0.5.2)
OS Support: Windows 7, 8, 10, 11 (32/64-bit)
Purpose: Restore corrupted USB drives, change capacity settings, burn-in test, create CD-ROM partitions, and recover fake-capacity drives.
When complete, the status bar turns green and shows PASS. Total capacity should show as 8GB, 16GB, 32GB, etc. – not 0.
Because direct links in posts often expire, the best reliable source for this specific version is usually usbdev.ru. Search there for "FirstChip MPTools FC1178" to find the v1.0.5.2 download link.
Disclaimer: I cannot provide direct download links to unofficial third-party software repositories. Please proceed with caution when downloading executable files from the internet. firstchip fc1178 fc1179 mptools v1052 install
How to Install and Use FirstChip FC1178/FC1179 MPTools V1.0.5.2
If you have a USB flash drive that is corrupted, showing "Write Protected," or reporting "No Media," you likely need a Mass Production Tool (MPTool) to perform a low-level format. For drives using the FirstChip FC1178 or FC1179 controllers, the MPTools V1.0.5.2 is the specific utility designed to factory-reset these chips.
This guide covers the installation and basic operation of the V1.0.5.2 software. Prerequisites Before starting, ensure you have the following:
Chip Verification: Use a tool like ChipGenius to confirm your controller is indeed a FirstChip FC1178 or FC1179. Using the wrong software can permanently "brick" your drive.
OS Compatibility: These tools run best on Windows 7 or Windows 10. If you are on Windows 11, you may need to run the application in "Compatibility Mode."
Backup Data: This process is destructive. All data on the USB drive will be permanently erased. Step 1: Downloading and Unpacking
Since FirstChip tools are often distributed as portable RAR or ZIP archives, there isn't a traditional "installer." | Problem | Solution | |---------|----------| | Drive
Download the FirstChip_MpTool_20201118_8T24_V1.0.5.2 package from a reputable firmware archive. Extract the folder to your C: drive or Desktop.
Tip: Avoid long file paths or folders with special characters, as these can cause the software to crash. Step 2: Running the Tool
Open the extracted folder and locate the executable file (usually named FirstChip_MpTool.exe).
Right-click the file and select Run as Administrator. This is crucial for the software to access the low-level USB drivers. Step 3: Configuring the MPTool
Once the interface opens, it should automatically detect your USB drive in one of the numbered slots.
Settings/Binning: Click on the "Settings" button (you may need to leave the password blank or try "123456"). Scan Mode: For general repairs, select "Low Level Format." If you are trying to recover capacity, select "Default."
Flash Select: In most cases, "Auto" is sufficient, but if the tool fails, you may need to manually select your flash memory type from the dropdown list. Step 4: The Flashing Process Before formatting, you must load the correct parameters
Click OK to save your settings and return to the main screen. Press the "Start" button.
The status bar will change colors (usually yellow for processing and green for success). This can take anywhere from 2 minutes to an hour depending on the size of the drive and the "Scan Level" chosen. Troubleshooting Common Issues
Device Not Found: Try a different USB port (preferably a USB 2.0 port on the back of the motherboard). Avoid using USB hubs.
"Code 4" Error: This often indicates a hardware failure in the NAND chip or an incorrect firmware version. Ensure you are using the V1.0.5.2 version specifically if your chip was manufactured around late 2020.
Write Protect remains: You may need to select "Erase All" in the settings before running the Start process.
The FirstChip FC1178/FC1179 MPTools V1.0.5.2 is a powerful utility for reviving "dead" flash drives. By following the low-level format path, you can bypass most software-level write protections and file system errors.